The text of and illustrations in this document are licensed by Red Hat
under a Creative Commons Attribution–Share Alike 3.0 Unported license
("CC-BY-SA"). An explanation of CC-BY-SA is available at http://creativecommons.org/licenses/by-sa/3.0/.
In accordance with CC-BY-SA, if you distribute this document or an
adaptation of it, you must provide the URL for the original version.
Red Hat, as the licensor of this document, waives the right to
enforce, and agrees not to assert, Section 4d of CC-BY-SA to the fullest
extent permitted by applicable law.
Red Hat, Red Hat Enterprise Linux, the Shadowman logo, JBoss,
MetaMatrix, Fedora, the Infinity Logo, and RHCE are trademarks of Red
Hat, Inc., registered in the United States and other countries.
Linux® is the registered trademark of Linus Torvalds in the United States and other countries.
Java® is a registered trademark of Oracle and/or its affiliates.
XFS® is a trademark of Silicon Graphics International Corp. or its subsidiaries in the United States and/or other countries.
MySQL® is a registered trademark of MySQL AB in the United States, the European Union and other countries.
All other trademarks are the property of their respective owners.
This document explains how to manage power consumption on Red Hat
Enterprise Linux 6 systems effectively. The following sections discuss
different techniques that lower power consumption (for both server and
laptop), and how each technique affects the overall performance of your
system.
This manual uses several conventions to highlight certain words and
phrases and draw attention to specific pieces of information.
In PDF and paper editions, this manual uses typefaces drawn from the Liberation Fonts
set. The Liberation Fonts set is also used in HTML editions if the set
is installed on your system. If not, alternative but equivalent
typefaces are displayed. Note: Red Hat Enterprise Linux 5 and later
includes the Liberation Fonts set by default.
1.1. Typographic Conventions
Four typographic conventions are used to call attention to specific
words and phrases. These conventions, and the circumstances they apply
to, are as follows.
Mono-spaced Bold
Used to highlight system input, including shell commands, file names
and paths. Also used to highlight keycaps and key combinations. For
example:
To see the contents of the file my_next_bestselling_novel in your current working directory, enter the cat my_next_bestselling_novel command at the shell prompt and press Enter to execute the command.
The above includes a file name, a shell command and a keycap, all
presented in mono-spaced bold and all distinguishable thanks to context.
Key combinations can be distinguished from keycaps by the hyphen connecting each part of a key combination. For example:
Press Enter to execute the command.
Press Ctrl+Alt+F2 to switch to the first virtual terminal. Press Ctrl+Alt+F1 to return to your X-Windows session.
The first paragraph highlights the particular keycap to press. The
second highlights two key combinations (each a set of three keycaps with
each set pressed simultaneously).
If source code is discussed, class names, methods, functions,
variable names and returned values mentioned within a paragraph will be
presented as above, in mono-spaced bold. For example:
File-related classes include filesystem for file systems, file for files, and dir for directories. Each class has its own associated set of permissions.
Proportional Bold
This denotes words or phrases encountered on a system, including
application names; dialog box text; labeled buttons; check-box and radio
button labels; menu titles and sub-menu titles. For example:
Choose System → Preferences → Mouse from the main menu bar to launch Mouse Preferences. In the Buttons tab, click the Left-handed mouse check box and click Close to switch the primary mouse button from the left to the right (making the mouse suitable for use in the left hand).
To insert a special character into a gedit file, choose Applications → Accessories → Character Map from the main menu bar. Next, choose Search → Find… from the Character Map menu bar, type the name of the character in the Search field and click Next. The character you sought will be highlighted in the Character Table. Double-click this highlighted character to place it in the Text to copy field and then click the Copy button. Now switch back to your document and choose Edit → Paste from the gedit menu bar.
The above text includes application names; system-wide menu names and
items; application-specific menu names; and buttons and text found
within a GUI interface, all presented in proportional bold and all
distinguishable by context.
Mono-spaced Bold Italic or Proportional Bold Italic
Whether mono-spaced bold or proportional bold, the addition of
italics indicates replaceable or variable text. Italics denotes text you
do not input literally or displayed text that changes depending on
circumstance. For example:
To connect to a remote machine using ssh, type ssh username@domain.name at a shell prompt. If the remote machine is example.com and your username on that machine is john, type ssh john@example.com.
The mount -o remount file-system command remounts the named file system. For example, to remount the /home file system, the command is mount -o remount /home.
To see the version of a currently installed package, use the rpm -q package command. It will return a result as follows: package-version-release.
Note the words in bold italics above — username, domain.name,
file-system, package, version and release. Each word is a placeholder,
either for text you enter when issuing a command or for text displayed
by the system.
Aside from standard usage for presenting the title of a work, italics
denotes the first use of a new and important term. For example:
Publican is a DocBook publishing system.
1.2. Pull-quote Conventions
Terminal output and source code listings are set off visually from the surrounding text.
Output sent to a terminal is set in mono-spaced roman and presented thus:
Finally, we use three visual styles to draw attention to information that might otherwise be overlooked.
Note
Notes are tips, shortcuts or alternative approaches to the task at
hand. Ignoring a note should have no negative consequences, but you
might miss out on a trick that makes your life easier.
Important
Important boxes detail things that are easily missed: configuration
changes that only apply to the current session, or services that need
restarting before an update will apply. Ignoring a box labeled
'Important' will not cause data loss but may cause irritation and
frustration.
Warning
Warnings should not be ignored. Ignoring warnings will most likely cause data loss.
2. Getting Help and Giving Feedback
2.1. Do You Need Help?
If you experience difficulty with a procedure described in this documentation, visit the Red Hat Customer Portal at http://access.redhat.com. Through the customer portal, you can:
search or browse through a knowledgebase of technical support articles about Red Hat products.
submit a support case to Red Hat Global Support Services (GSS).
access other product documentation.
Red Hat also hosts a large number of electronic mailing lists for
discussion of Red Hat software and technology. You can find a list of
publicly available mailing lists at https://www.redhat.com/mailman/listinfo. Click on the name of any mailing list to subscribe to that list or to access the list archives.
2.2. We Need Feedback!
If you find a typographical error in this manual, or if you have
thought of a way to make this manual better, we would love to hear from
you! Please submit a report in Bugzilla: http://bugzilla.redhat.com/ against the product Red_Hat_Enterprise_Linux.
When submitting a bug report, be sure to mention the manual's identifier: doc-Power_Management_Guide
If you have a suggestion for improving the documentation, try to be
as specific as possible when describing it. If you have found an error,
please include the section number and some of the surrounding text so we
can find it easily.
Power management has been one of our focus points for improvements for
Red Hat Enterprise Linux 6. Limiting the power used by computer systems
is one of the most important aspects of green IT
(environmentally friendly computing), a set of considerations that also
encompasses the use of recyclable materials, the environmental impact
of hardware production, and environmental awareness in the design and
deployment of systems. In this document, we provide guidance and
information regarding power management of your systems running Red Hat
Enterprise Linux 6.
1.1. Importance of Power Management
At the core of power management is an understanding of how to
effectively optimize energy consumption of each system component. This
entails studying the different tasks that your system performs, and
configuring each component to ensure that its performance is just right
for the job.
The main motivator for power management is:
reducing overall power consumption to save cost
The proper use of power management results in:
heat reduction for servers and computing centers
reduced secondary costs, including cooling, space, cables, generators, and uninterruptible power supplies (UPS)
extended battery life for laptops
lower carbon dioxide output
meeting government regulations or legal requirements regarding Green IT, for example Energy Star
meeting company guidelines for new systems
As a rule, lowering the power consumption of a specific component (or
of the system as a whole) will lead to lower heat and naturally,
performance. As such, you should thoroughly study and test the decrease
in performance afforded by any configurations you make, especially for
mission-critical systems.
By studying the different tasks that your system performs, and
configuring each component to ensure that its performance is just
sufficient for the job, you can save energy, generate less heat, and
optimize battery life for laptops. Many of the principles for analysis
and tuning of a system in regard to power consumption are similar to
those for performance tuning. To some degree, power management and
performance tuning are opposite approaches to system configuration,
because systems are usually optimized either towards performance or
power. This manual describes the tools that Red Hat provides and the
techniques we have developed to help you in this process.
Red Hat Enterprise Linux 6 already comes with a lot of new power
management features that are enabled by default. They were all
selectively chosen to not impact the performance of a typical server or
desktop use case. However, for very specific use cases where maximum
throughput, lowest latency, or highest CPU performance is absolutely
required, a review of those defaults might be necessary.
To decide whether you should optimize your machines using the
techniques described in this document, ask yourself a few questions:
The importance of power optimization depends on whether your
company has guidelines that need to be followed or if there are any
regulations that you have to fulfill.
How much do I need to optimize?
Several of the techniques we present do not require you to go
through the whole process of auditing and analyzing your machine in
detail but instead offer a set of general optimizations that typically
improve power usage. Those will of course typically not be as good as a
manually audited and optimized system, but provide a good compromise.
Will optimization reduce system performance to an unacceptable level?
Most of the techniques described in this document impact the
performance of your system noticeably. If you choose to implement power
management beyond the defaults already in place in Red Hat Enterprise
Linux 6, you should monitor the performance of the system after power
optimization and decide if the performance loss is acceptable.
Will the time and resources spent to optimize the system outweigh the gains achieved?
Optimizing a single system manually following the whole process is
typically not worth it as the time and cost spent doing so is far
higher than the typical benefit you would get over the lifetime of a
single machine. On the other hand if you for example roll out 10000
desktop systems to your offices all using the same configuration and
setup then creating one optimized setup and applying that to all 10000
machines is most likely a good idea.
The following sections will explain how optimal hardware performance benefits your system in terms of energy consumption.
1.2. Power Management Basics
Effective power management is built on the following principles:
An idle CPU should only wake up when needed
The Red Hat Enterprise Linux 5 kernel used a periodic timer for each
CPU. This timer prevents the CPU from truly going idle, as it requires
the CPU to process each timer event (which would happen every few
milliseconds, depending on the setting), regardless of whether any
process was running or not. A large part of effective power management
involves reducing the frequency at which CPU wakeups are made.
Because of this, the Linux kernel in Red Hat Enterprise Linux 6
eliminates the periodic timer: as a result, the idle state of a CPU is
now tickless. This prevents the CPU from
consuming unnecessary power when it is idle. However, benefits from this
feature can be offset if your system has applications that create
unnecessary timer events. Polling events (such as checks for volume
changes, mouse movement, and the like) are examples of such events.
Red Hat Enterprise Linux 6 includes tools with which you can identify
and audit applications on the basis of their CPU usage. Refer to Chapter 2, Power management auditing and analysis for details.
Unused hardware and devices should be disabled completely
This is especially true for devices that have moving parts (for
example, hard disks). In addition to this, some applications may leave
an unused but enabled device "open"; when this occurs, the kernel
assumes that the device is in use, which can prevent the device from
going into a power saving state.
Low activity should translate to low wattage
In many cases, however, this depends on modern hardware and correct
BIOS configuration. Older system components often do not have support
for some of the new features that we now can support in Red Hat
Enterprise Linux 6. Make sure that you are using the latest official
firmware for your systems and that in the power management or device
configuration sections of the BIOS the power management features are
enabled. Some features to look for include:
SpeedStep
PowerNow!
Cool'n'Quiet
ACPI (C state)
Smart
If your hardware has support for these features and they are enabled
in the BIOS, Red Hat Enterprise Linux 6 will use them by default.
Different forms of CPU states and their effects
Modern CPUs together with Advanced Configuration and Power Interface (ACPI) provide different power states. The three different states are:
Sleep (C-states)
Frequency (P-states)
Heat output (T-states or "thermal states")
A CPU running on the lowest sleep state possible consumes the least
amount of watts, but it also takes considerably more time to wake it up
from that state when needed. In very rare cases this can lead to the CPU
having to wake up immediately every time it just went to sleep. This
situation results in an effectively permanently busy CPU and loses some
of the potential power saving if another state had been used.
A turned off machine uses the least amount of power
As obvious as this might sound, one of the best ways to actually save
power is to turn off systems. For example, your company can develop a
corporate culture focused on "green IT" awareness with a guideline to
turn of machines during lunch break or when going home. You also might
consolidate several physical servers into one bigger server and
virtualize them using the virtualization technology we ship with Red Hat
Enterprise Linux 6.
The detailed manual audit, analysis, and tuning of a single system is
usually the exception because the time and cost spent to do so typically
outweighs the benefits gained from these last pieces of system tuning.
However, performing these tasks once for a large number of nearly
identical systems where you can reuse the same settings for all systems
can be very useful. For example, consider the deployment of thousands of
desktop systems, or a HPC cluster where the machines are nearly
identical. Another reason to do auditing and analysis is to provide a
basis for comparison against which you can identify regressions or
changes in system behavior in the future. The results of this analysis
can be very helpful in cases where hardware, BIOS, or software updates
happen regularly and you want to avoid any surprises with regard to
power consumption. Generally, a thorough audit and analysis gives you a
much better idea of what is really happening on a particular system.
Auditing and analyzing a system with regard to power consumption is
relatively hard, even with the most modern systems available. Most
systems do not provide the necessary means to measure power use via
software. Exceptions exist though: the ILO management console of Hewlett
Packard server systems has a power management module that you can
access through the web. IBM provides a similar solution in their
BladeCenter power management module. On some Dell systems, the IT
Assistant offers power monitoring capabilities as well. Other vendors
are likely to offer similar capabilities for their server platforms, but
as can be seen there is no single solution available that is supported
by all vendors. If your system has no inbuilt mechanism to measure power
consumption, a few other choices exist. You could install a special
power supply for your system that offers power consumption information
through USB. The Gigabyte Odin GT 550 W PC power supply is one such example, and software to read out those values under Linux is available externally from http://mgmt.sth.sze.hu/~andras/dev/gopsu/. As a last resort, some external watt meters like the Watts up? PRO have a USB connector.
Direct measurements of power consumption is often only necessary to
maximize savings as far as possible. Fortunately, other means are
available to measure if changes are in effect or how the system is
behaving. This chapter describes the necessary tools.
2.2. PowerTOP
The introduction of the tickless kernel in Red Hat Enterprise Linux 6 (refer to Section 3.4, “Tickless Kernel”) allows the CPU to enter the idle state more frequently, reducing power consumption and improving power management. The new PowerTOP tool identifies specific components of kernel and userspace applications that frequently wake up the CPU. PowerTOP was used in development to perform the audits described in Section 3.11, “Optimizations in User Space” that led to many applications being tuned in this release, reducing unnecessary CPU wake up by a factor of ten.
Install PowerTOP with the command:
yum install powertop
Run PowerTOP with the command:
powertop
Note that you will need to run PowerTOP with root privileges to allow the application to do anything useful.
When it runs, PowerTOP
gathers statistics from the system and presents you with a list of the
components that are sending wakeups to the CPU most frequently. PowerTOP
also makes suggestions for tuning the system for lower power
consumption. These suggestions appear at the bottom of the screen, and
specify a key for you to press to accept PowerTOP's suggestion. As PowerTOP refreshes periodically, further suggestions appear. In Figure 2.1, “PowerTOP in Operation”, note the suggestion to increase the VM dirty writeback time, and the key (W) to press to accept the suggestion.
When it runs, PowerTOP
gathers statistics from the system and presents you with several
important lists of information. At the top is a list of how long your
CPU cores have been in each of the available C and P states. The longer
the CPU stays in the higher C or P stats the better (C4 being higher than C3)
and is a good indicator of how well the system is tuned towards CPU
utilization. Your goal should be residency of 90% or more in the highest
C or P state while the system is idle.
The second piece of information is a summary of the actual wakeups per
second of the machine. The number of wakeups per second gives you a
good measure of how well the services or the devices and drivers of the
kernel are performing with regard to power usage on your system. The
more wakeups per second you have, the more power is consumed, so lower
is better here.
Next, PowerTOP provides an estimate of the actual power usage of the system, if available. Expect PowerTOP to report this figure on laptops while they are in battery mode.
Any available estimates of power usage are followed by a detailed list
of the components that send wakeups to the CPU most frequently. At the
top of the list are those components that you should investigate more
closely to optimize your system to reduce power usage. If they are
kernel components, (indicated by the name of the component being listed
in <>)
then the wakeups are often associated with a specific driver that causes
them. Tuning drivers most usually requires kernel changes which go
beyond the scope of this document. However, userland processes that send
wakeups are more easily managed. First, identify if this service or
application should run at all on this system. If not, simply deactivate
it. To turn off a service permanently, run:
chkconfig servicename off
If you need more details about the what the component actually does, run:
ps -awux | grep componentnamestrace -p processid
If the trace looks like it is repeating itself, then you probably have
found a busy loop. To fix this would require a code change in that
component and that again goes beyond the scope of this document.
Finally, PowerTOP
also makes suggestions for tuning the system for lower power
consumption. These suggestions appear at the bottom of the screen, and
specify a key for you to press to accept PowerTOP's suggestion. As PowerTOP refreshes periodically, further suggestions appear. In Figure 2.1, “PowerTOP in Operation”, note the suggestion to increase the VM dirty writeback time, and the key (W)
to press to accept the suggestion. These changes will only be active
until the next reboot. To help you make the changes permanent, PowerTOP displays the exact command it runs to perform this optimization. Add the command to your /etc/rc.local file with your preferred text editor so that it takes effect every time that the computer starts.
Diskdevstat and netdevstat are SystemTap
tools that collect detailed information about the disk activity and
network activity of all applications running on a system. These tools
were inspired by PowerTOP, which shows the number of CPU wakeups by every application per second (refer to Section 2.2, “PowerTOP”).
The statistics that these tools collect allow you to identify
applications that waste power with many small I/O operations rather than
fewer, larger operations. Other monitoring tools that measure only
transfer speeds do not help to identify this type of usage.
Install these tools with SystemTap with the command:
These three applications have a WRITE_CNT greater than 0, which means that they performed some form of write during the measurement. Of those, plasma
was the worst offender by a large degree: it performed the most write
operations, and of course the average time between writes was the
lowest. Plasma would therefore be the best candidate to investigate if you were concerned about power-inefficient applications.
Use the strace and ltrace
commands to examine applications more closely by tracing all system
calls of the given process ID. In the present example, you could run:
strace -p 2789
In this example, the output of the strace
contained a repeating pattern every 45 seconds that opened the KDE icon
cache file of the user for writing followed by an immediate close of
the file again. This led to a necessary physical write to the hard disk
as the file metadata (specifically, the modification time) had changed.
The final fix was to prevent those unnecessary calls when no updates to
the icons had occurred.
2.4. Battery Life Tool Kit
Red Hat Enterprise Linux 6 introduces the Battery Life Tool Kit (BLTK), a test suite that simulates and analyzes battery life and performance. BLTK
achieves this by performing sets of tasks that simulate specific user
groups and reporting on the results. Although developed specifically to
test notebook performance, BLTK can also report on the performance of desktop computers when started with the -a.
BLTK allows you to generate very reproducible workloads that are comparable to real use of a machine. For example, the office workload writes a text, corrects things in it, and does the same for a spreadsheet. Running BLTK combined with PowerTOP
or any of the other auditing or analysis tool allows you to test if the
optimizations you performed have an effect when the machine is actively
in use instead of only idling. Because you can run the exact same
workload multiple times for different settings, you can compare results
for different settings.
Install BLTK with the command:
yum install bltk
Run BLTK with the command:
bltk workloadoptions
For example, to run the idle workload for 120 seconds:
bltk -I -T 120
The workloads available by default are:
-I, --idle
system is idle, to use as a baseline for comparison with other workloads
-R, --reader
simulates reading documents (by default, with Firefox)
-P, --player
simulates watching multimedia files from a CD or DVD drive (by default, with mplayer)
-O, --office
simulates editing documents with the OpenOffice.org suite
Other options allow you to specify:
-a, --ac-ignore
ignore whether AC power is available (necessary for desktop use)
-T number_of_seconds, --time number_of_seconds
the time (in seconds) over which to run the test; use this option with the idle workload
-F filename, --file filename
specifies a file to be used by a particular workload, for example, a file for the player workload to play instead of accessing the CD or DVD drive
-W application, --prog application
specifies an application to be used by a particular workload, for example, a browser other than Firefox for the reader workload
BLTK supports a large number of more specialized options. For details, refer to the bltk man page.
BLTK saves the results that it generates in a directory specified in the /etc/bltk.conf configuration file — by default, ~/.bltk/workload.results.number/. For example, the ~/.bltk/reader.results.002/ directory holds the results of the third test with the reader
workload (the first test is not numbered). The results are spread
across several text files. To condense these results into a format that
is easy to read, run:
bltk_report path_to_results_directory
The results now appear in a text file named Report in the results directory. To view the results in a terminal emulator instead, use the -o option:
bltk_report -o path_to_results_directory
2.5. Tuned and ktune
Tuned is a daemon
that monitors the use of system components and dynamically tunes system
settings based on that monitoring information. Dynamic tuning accounts
for the way that various system components are used differently
throughout the uptime for any given system. For example, the hard drive
is used heavily during startup and login, but is barely used later when a
user might mainly work with applications like OpenOffice or email
clients. Similarly, the CPU and network devices are used differently at
different times. Tuned monitors the activity of these components and reacts to changes in their use.
As a practical example, consider a typical office workstation. Most of
the time, the Ethernet network interface will be very inactive. Only a
few emails will go in and out every once in a while or some web pages
might be loaded. For those kinds of loads, the network interface doesn't
have to run at full speed all the time, as it does by default. Tuned
has a monitoring and tuning plugin for network devices that can detect
that low activity and then automatically lower the speed of that
interface, typically resulting in lower power usage. If activity on the
interface increases drastically for a longer period of time, for example
because a DVD image is being downloaded or an email with a large
attachment is opened, tuned
detects this and sets the interface speed to maximum to offer the best
performance while the activity level is so high. This principle is used
for the other plugins for CPU and hard disks as well.
Network devices are not configured to behave this way by default
because speed changes can take several seconds to take effect and
therefore directly and visibly impact the user experience. Similar
considerations apply for the CPU and hard drive tuning plugins. When a
hard drive has been spun down, it can take several seconds for it to
spin up again which results in an observed lack of responsiveness of the
system during that period. The latency side effect is smallest for the
CPU plugin, but it is still at least measurable, though hardly
noticeable by a user.
Alongside of tuned we now also offer ktune. Ktune
was introduced in Red Hat Enterprise Linux 5.3 as a framework and
service to optimize the performance of a machine for a specific use
cases. Since then, ktune
has improved to such a degree that we now use it as the static part of
our general tuning framework. It is mainly used in the different
predefined profiles described in Section 2.5.2, “Tuned-adm”.
Install the tuned package and its associated systemtap scripts with the command:
yum install tuned
Installing the tuned package also sets up a sample configuration file at /etc/tuned.conf and activates the default profile.
Start tuned by running:
service tuned start
To start tuned every time the machine boots, run:
chkconfig tuned on
Tuned itself has additional options that you can use when you run it manually. The available options are:
-d, --daemon
start tuned as a daemon instead of in the foreground.
-c, --conffile
use a configuration file with the specified name and path, for example, --conffile=/etc/tuned2.conf. The default is /etc/tuned.conf.
-D, --debug
use the highest level of logging.
2.5.1. The tuned.conf file
The tuned.conf file contains configuration settings for tuned. By default, it is located at /etc/tuned.conf, but you can specify a different name and location by starting tuned with the --conffile option.
The config file must always contain a [main] section that defines the general parameters for tuned. The file then contains a section for each plugin.
The [main] section contains the following options:
interval
the interval at which tuned should monitor and tune the system, in seconds. The default value is 10.
verbose
specifies whether output should be verbose. The default value is False.
logging
specifies the minimum priority of messages to be logged. In descending order, allowable values are: critical, error, warning, info, and debug. The default value is info.
logging_disable
specifies the maximum priority of messages to be logged; any
messages with this priority or lower will not be logged. In descending
order, allowable values are: critical, error, warning, info, and debug. The value notset disables this option.
Each plugin has its own section, specified with the name of the plugin in square brackets; for example: [CPUTuning]. Each plugin can have its own options, but the following apply to all plugins:
enabled
specifies whether the plugin is enabled or not. The default value is True.
verbose
specifies whether output should be verbose. If not set for this plugin, the value is inherited from [main].
logging
specifies the minimum priority of messages to be logged. If not set for this plugin, the value is inherited from [main].
A sample config file follows:
[main]
interval=10
pidfile=/var/run/tuned.pid
logging=info
logging_disable=notset
# Disk monitoring section
[DiskMonitor]
enabled=True
logging=debug
# Disk tuning section
[DiskTuning]
enabled=True
hdparm=False
alpm=False
logging=debug
# Net monitoring section
[NetMonitor]
enabled=True
logging=debug
# Net tuning section
[NetTuning]
enabled=True
logging=debug
# CPU monitoring section
[CPUMonitor]
# Enabled or disable the plugin. Default is True. Any other value
# disables it.
enabled=True
# CPU tuning section
[CPUTuning]
# Enabled or disable the plugin. Default is True. Any other value
# disables it.
enabled=True
2.5.2. Tuned-adm
Often, a detailed audit and analysis of a system can be very time
consuming and might not be worth the few extra watts you might be able
to save by doing so. Previously, the only alternative was simply to use
the defaults. Therefore, Red Hat Enterprise Linux 6 includes separate
profiles for specific use cases as an alternative between those two
extremes, together with the tuned-adm
tool that allows you to switch between these profiles easily at the
command line. Red Hat Enterprise Linux 6 includes a number of predefined
profiles for typical use cases that you can simply select and activate
with the tuned-adm command, but you can also create, modify or delete profiles yourself.
To list all available profiles and identify the current active profile, run:
tuned-adm list
To only display the currently active profile, run:
tuned-adm active
To switch to one of the available profiles, run:
tuned-adm profile profile_name
for example:
tuned-adm profile server-powersave
To disable all tuning:
tuned-adm off
When you first install tuned, the default profile will be active. Red Hat Enterprise Linux 6 also includes the following predefined profiles:
default
the default power-saving profile. It has the lowest impact on
power saving of the available profiles and only enables CPU and disk
plugins of tuned.
desktop-powersave
a power-saving profile directed at desktop systems. Enables ALPM power saving for SATA host adapters (refer to Section 3.6, “Aggressive Link Power Management”) as well as the CPU, Ethernet, and disk plugins of tuned.
server-powersave
a power-saving profile directed at server systems. Enables ALPM
powersaving for SATA host adapters, disables CD-ROM polling through HAL (refer to the hal-disable-polling man page) and activates the CPU and disk plugins of tuned.
laptop-ac-powersave
a medium-impact power-saving profile directed at laptops running
on AC. Enables ALPM powersaving for SATA host adapters, WiFi power
saving, as well as the CPU, Ethernet and disk plugins of tuned.
laptop-battery-powersave
a high-impact power-saving profile directed at laptops running on
battery. It activates all power saving mechanisms from the previous
profiles plus it enables the multi-core power-savings scheduler for low
wakeup systems and makes sure that the ondemand governor is active and
that AC97 audio power-saving is enabled. You can use this profile to
save the maximum amount of power on any kind of system, not only laptops
on battery power. The tradeoff for this profile is a noticeable impact
on performance, specifically latency of disk and network I/O.
throughput-performance
a server profile for typical throughput performance tuning. It disables tuned and ktune power saving mechanisms, enables sysctl settings that improve the throughput performance of your disk and network I/O, and switches to the deadline scheduler.
latency-performance
a server profile for typical latency performance tuning. it disables tuned and ktune power saving mechanisms and enables sysctl settings that improve the latency performance of your network I/O.
All the profiles are stored in separate subdirectories under /etc/tune-profiles. So /etc/tune-profiles/desktop-powersave contains all the necessary files and settings for that profile. Each of these directories contains up to four files:
tuned.conf
the configuration for the tuned service to be active for this profile.
sysctl.ktune
the sysctl settings used by ktune. The format is identical to the /etc/sysconfig/sysctl file (refer to the sysctl and sysctl.conf man pages).
ktune.sysconfig
the configuration file of ktune itself, typically /etc/sysconfig/ktune.
ktune.sh
an init-style shell script used by the ktune service which can run specific commands during system startup to tune the system.
The easiest way to start a new profile is to copy an existing one. The laptop-battery-powersave
profile contains a very rich set of tunings already and is therefore a
useful starting point. Simply copy the whole directory to the new
profile name like this:
cp -a /etc/tune-profiles/laptop-battery-powersave/ /etc/tune-profiles/myprofile
Modify any of the files in the new profile to match your personal
requirements. For example, if you require the detection of CD changes
you could disable that optimization by commenting out the appropriate
line in the ktune.sh script:
# Disable HAL polling of CDROMS
# for i in /dev/scd*; do hal-disable-polling --device $i; done > /dev/null 2>&1
2.6. DeviceKit-power and devkit-power
In Red Hat Enterprise Linux 6 DeviceKit-power assumes the power management functions that were part of HAL and some of the functions that were part of GNOME Power Manager in previous releases of Red Hat Enterprise Linux (refer also to Section 2.7, “GNOME Power Manager”. DeviceKit-power
provides a daemon, an API, and a set of command-line tools. Each power
source on the system is represented as a device, whether it is a
physical device or not. For example, a laptop battery and an AC power
source are both represented as devices.
You can access the command-line tools with the devkit-power command and the following options:
--enumerate, -e
displays an object path for each power devices on the system, for example:
displays the parameters for all power devices on the system.
--wakeups, -w
displays the CPU wakeups on the system.
--monitor, -m
monitors the system for changes to power devices, for example, the
connection or disconnection of a source of AC power, or the depletion of
a battery. Press Ctrl+C to stop monitoring the system.
--monitor-detail
monitors the system for changes to power devices, for example, the
connection or disconnection of a source of AC power, or the depletion of
a battery. The --monitor-detail option presents more detail than the --monitor option. Press Ctrl+C to stop monitoring the system.
--show-info object_path, -i object_path
displays all information available for a particular object path.
For example, to obtain information about a battery on your system
represented by the object path /org/freedesktop/UPower/DeviceKit/power/battery_BAT0, run:
GNOME Power Manager is a daemon that is installed as part of the GNOME desktop. Much of the power-management functionality that GNOME Power Manager provided in earlier versions of Red Hat Enterprise Linux has become part of DeviceKit-power in Red Hat Enterprise Linux 6 (refer to Section 2.6, “DeviceKit-power and devkit-power”. However, GNOME Power Manager remains a front end for that functionality. Through an applet in the system tray, GNOME Power Manager
notifies you of changes in your system's power status; for example, a
change from battery to AC power. It also reports battery status, and
warns you when battery power is low.
GNOME Power Manager also allows you to configure some basic power management settings. To access these settings, click the GNOME Power Manager icon in the system tray, then click Preferences
The Power Management Preferences screen contains three tabs:
On AC Power
On Battery Power
General
Use the On AC Power and On Battery Power
tabs to specify how much time must pass before the display is turned
off on an inactive system, how much time must pass before an inactive
system is put to sleep, and whether the system should spin down hard
disks when not in use. The On Battery Power
tab also allows you to set the display brightness and to choose a
behavior for a system with a critically low battery. For example, by
default, GNOME Power Manager makes a system hibernate when its battery level reaches a critically low level. Use the General
tab to set behaviours for the (physical) power button and suspend
button on your system, and to specify the circumstances under which the GNOME Power Manager icon should appear in the system tray.
2.8. Other means for auditing
Red Hat Enterprise Linux 6 offers quite a few more tools with which to
perform system auditing and analysis. Most of them can be used as a
supplementary sources of information in case you want to verify what you
have discovered already or in case you need more in-depth information
on certain parts. Many of these tools are used for performance tuning as
well. They include:
vmstat
vmstat gives you
detailed information about processes, memory, paging, block I/O, traps,
and CPU activity. Use it to take a closer look at what the system
overall does and where it is busy.
iostat
iostat is similar to vmstat, but only for I/O on block devices. It also provides more verbose output and statistics.
blktrace
blktrace is a
very detailed block I/O trace program. It breaks down information to
single blocks associated with applications. It is very useful in
combination with diskdevstat.
CPUs with the x86 architecture support various states in which parts
of the CPU are deactivated or run at lower performance settings. These
states, known as C-states, allow systems to
save power by partially deactivating CPUs that are not in use. C-states
are numbered from C0 upwards, with higher numbers representing decreased
CPU functionality and greater power saving. C-States of a given number
are broadly similar across processors, although the exact details of the
specific feature sets of the state may vary between processor families.
C-States 0–3 are defined as follows:
C0
the operating or running state. In this state, the CPU is working and not idle at all.
C1, Halt
a state where the processor is not executing any instructions but
is typically not in a lower power state. The CPU can continue processing
with practically no delay. All processors offering C-States need to
support this state. Pentium 4 processors support an enhanced C1
state called C1E that actually is a state for lower power consumption.
C2, Stop-Clock
a state where the the clock is frozen for this processor but it
keeps the complete state for its registers and caches, so after starting
the clock again it can immediately start processing again. This is an
optional state.
C3, Sleep
a state where the processor really goes to sleep and doesn't need
to keep it's cache up to date. Waking up from this state takes
considerably longer than from C2 due to this. Again this is an optional
state.
Recent Intel CPUs with the "Nehalem" microarchitecture feature a new
C-State, C6, which can reduce the voltage supply of a CPU to zero, but
typically reduces power consumption by between 80% and 90%. The kernel
in Red Hat Enterprise Linux 6 includes optimizations for this new
C-State.
3.2. Using CPUfreq Governors
One of the most effective ways to reduce power consumption and heat
output on your system is to use CPUfreq. CPUfreq — also referred to as
CPU speed scaling — allows the clock speed of the processor to be
adjusted on the fly. This enables the system to run at a reduced clock
speed to save power. The rules for shifting frequencies, whether to a
faster or slower clock speed, and when to shift frequencies, are defined
by the CPUfreq governor.
The governor defines the power characteristics of the system CPU,
which in turn affects CPU performance. Each governor has its own unique
behavior, purpose, and suitability in terms of workload. This section
describes how to choose and configure a CPUfreq governor, the
characteristics of each governor, and what kind of workload each
governor is suitable for.
3.2.1. CPUfreq Governor Types
This section lists and describes the different types of CPUfreq governors available in Red Hat Enterprise Linux 6.
cpufreq_performance
The Performance governor forces the CPU to use the highest possible
clock frequency. This frequency will be statically set, and will not
change. As such, this particular governor offers no power saving benefit. It is only suitable for hours of heavy workload, and even then only during times wherein the CPU is rarely (or never) idle.
cpufreq_powersave
By contrast, the Powersave governor forces the CPU to use the lowest
possible clock frequency. This frequency will be statically set, and
will not change. As such, this particular governor offers maximum power
savings, but at the cost of the lowest CPU performance.
The term "powersave" can sometimes be deceiving, though, since (in
principle) a slow CPU on full load consumes more power than a fast CPU
that is not loaded. As such, while it may be advisable to set the CPU to
use the Powersave governor during times of expected low activity, any
unexpected high loads during that time can cause the system to actually
consume more power.
The Powersave governor is, in simple terms, more of a "speed limiter"
for the CPU than a "power saver". It is most useful in systems and
environments where overheating can be a problem.
cpufreq_ondemand
The Ondemand governor is a dynamic governor that allows the CPU to
achieve maximum clock frequency when system load is high, and also
minimum clock frequency when the system is idle. While this allows the
system to adjust power consumption accordingly with respect to system
load, it does so at the expense of latency between frequency switching.
As such, latency can offset any performance/power saving benefits
offered by the Ondemand governor if the system switches between idle and
heavy workloads too often.
For most systems, the Ondemand governor can provide the best
compromise between heat emission, power consumption, performance, and
manageability. When the system is only busy at specific times of the
day, the Ondemand governor will automatically switch between maximum and
minimum frequency depending on the load without any further
intervention.
cpufreq_userspace
The Userspace governor allows userspace programs (or any process
running as root) to set the frequency. This governor is normally used in
conjunction with the cpuspeed daemon. Of
all the governors, Userspace is the most customizable; and depending on
how it is configured, it can offer the best balance between performance
and consumption for your system.
cpufreq_conservative
Like the Ondemand governor, the Conservative governor also adjusts
the clock frequency according to usage (like the Ondemand governor).
However, while the Ondemand governor does so in a more aggressive manner
(that is from maximum to minimum and back), the Conservative governor
switches between frequencies more gradually.
This means that the Conservative governor will adjust to a clock
frequency that it deems fitting for the load, rather than simply
choosing between maximum and minimum. While this can possibly provide
significant savings in power consumption, it does so at an ever greater latency than the Ondemand governor.
Note
You can enable a governor using cron
jobs. This allows you to automatically set specific governors during
specific times of the day. As such, you can specify a low-frequency
governor during idle times (for example after work hours) and return to a
higher-frequency governor during hours of heavy workload.
Before selecting and configuring a CPUfreq governor, you need to add the appropriate CPUfreq driver first.
Procedure 3.1. How to Add a CPUfreq Driver
Use the following command to view which CPUfreq drivers are available for your system:
ls /lib/modules/[kernel version]/kernel/arch/[architecture]/kernel/cpu/cpufreq/
Use modprobe to add the appropriate CPUfreq driver.
modprobe [CPUfreq driver]
When using the above command, be sure to remove the .ko filename suffix.
Important
When choosing an appropriate CPUfreq driver, always choose acpi-cpufreq over p4-clockmod. While using the p4-clockmod driver reduces the clock frequency of a CPU, it does not reduce the voltage. acpi-cpufreq,
on the other hand, reduces voltage along with CPU clock frequency,
allowing less power consumption and heat output for each unit reduction
in performance.
Once the CPUfreq driver is set up, you can view which governor the system is currently using with:
Some CPUfreq governors may not be available for you to use. In this case, use modprobe
to add the necessary kernel modules that enable the specific CPUfreq
governor you wish to use. These kernel modules are available in /lib/modules/[kernel version]/kernel/drivers/cpufreq/.
Procedure 3.2. Enabling a CPUfreq Governor
If a specific governor is not listed as available for your CPU, use modprobe to enable the governor you wish to use. For example, if the ondemand governor is not available for your CPU, use the following command:
modprobe cpufreq_ondemand
Once a governor is listed as available for your CPU, you can enable it using:
Once you've chosen an appropriate CPUfreq governor, you can further tune the speed of each CPU using the tunables found in /sys/devices/system/cpu/[cpu ID]/cpufreq/. These tunables are:
cpuinfo_min_freq — Shows the CPU's available minimum operating frequency (in KHz).
cpuinfo_max_freq — Shows the CPU's available maximum operating frequency (in KHz).
scaling_driver — Shows what CPUfreq driver is used to set the frequency on this CPU.
cpuinfo_cur_freq — Shows the current speed of the CPU (in KHz).
scaling_available_frequencies — Lists available frequencies for the CPU, in KHz.
scaling_min_freq and scaling_max_freq — Sets the policy limits of the CPU, in KHz.
Important
When setting policy limits, you should set scaling_max_freq before scaling_min_freq.
affected_cpus — Lists CPUs that require frequency coordination software.
scaling_setspeed — Used to change the clock speed of the CPU, in KHz. You can only set a speed within the policy limits of the CPU (as per scaling_min_freq and scaling_max_freq).
To view the current value of each tunable, use cat [tunable]. For example, to view the current speed of cpu0 (in KHz), use:
To change the value of each tunable, use echo [value] > /sys/devices/system/cpu/[cpu ID]/cpufreq/[tunable]. For example, to set the minimum clock speed of cpu0 to 360 KHz, use:
When a system is suspended, the kernel calls on drivers to store their
states and then unloads them. When the system is resumed, it reloads
these drivers, which attempt to reprogram their devices. The drivers'
ability to accomplish this task determines whether the system can be
resumed successfully.
Video drivers are particularly problematic in this regard, because the Advanced Configuration and Power Interface
(ACPI) specification does not require system firmware to be able to
reprogram video hardware. Therefore, unless video drivers are able to
program hardware from a completely uninitialized state, they may prevent
the system from resuming.
Red Hat Enterprise Linux 6 includes greater support for new graphics
chipsets, which ensures that suspend and resume will work on a greater
number of platforms. In particular, support for NVIDIA chipsets has been
greatly improved; in particular for the GeForce 8800 series.
3.4. Tickless Kernel
Previously, the Linux kernel periodically interrupted each CPU on a
system at a predetermined frequency — 100 Hz, 250 Hz, or
1000 Hz, depending on the platform. The kernel queried the CPU
about the processes that it was executing, and used the results for
process accounting and load balancing. Known as the timer tick,
the kernel performed this interrupt regardless of the power state of
the CPU. Therefore, even an idle CPU was responding to up to 1000 of
these requests every second. On systems that implemented power saving
measures for idle CPUs, the timer tick prevented the CPU from remaining
idle long enough for the system to benefit from these power savings.
The kernel in Red Hat Enterprise Linux 6 runs tickless:
that is, it replaces the old periodic timer interrupts with on-demand
interrupts. Therefore, idle CPUs are allowed to remain idle until a new
task is queued for processing, and CPUs that have entered lower power
states can remain in these states longer.
3.5. Active-State Power Management
Active-State Power Management (ASPM) saves power in the Peripheral Component Interconnect Express
(PCI Express or PCIe) subsystem by setting a lower power state for PCIe
links when the devices to which they connect are not in use. ASPM
controls the power state at both ends of the link, and saves power in
the link even when the device at the end of the link is in a fully
powered-on state.
When ASPM is enabled, device latency increases because of the time
required to transition the link between different power states. ASPM has
three policies to determine power states:
default
sets PCIe link power states according to the defaults specified by
the firmware on the system (for example, BIOS). This is the default
state for ASPM.
powersave
sets ASPM to save power wherever possible, regardless of the cost to performance.
performance
disables ASPM to allow PCIe links to operate with maximum performance.
ASPM policies are set in /sys/module/pcie_aspm/parameters/policy, but can also be specified at boot time with the pcie_aspm kernel parameter, where pcie_aspm=off disables ASPM and pcie_aspm=force enables ASPM, even on devices that do not support ASPM.
Warning — pcie_aspm=force can cause systems to stop responding
If pcie_aspm=force is set, hardware that does not support ASPM can cause the system to stop responding. Before setting pcie_aspm=force, ensure that all PCIe hardware on the system supports ASPM.
3.6. Aggressive Link Power Management
Aggressive Link Power Management (ALPM) is a
power-saving technique that helps the disk save power by setting a SATA
link to the disk to a low-power setting during idle time (that is when
there is no I/O). ALPM automatically sets the SATA link back to an
active power state once I/O requests are queued to that link.
Power savings introduced by ALPM come at the expense of disk latency.
As such, you should only use ALPM if you expect the system to experience
long periods of idle I/O time.
When available, ALPM is enabled by default. ALPM has three modes:
min_power
This mode sets the link to its lowest power state (SLUMBER) when
there is no I/O on the disk. This mode is useful for times when an
extended period of idle time is expected.
medium_power
This mode sets the link to the second lowest power state (PARTIAL)
when there is no I/O on the disk. This mode is designed to allow
transitions in link power states (for example during times of
intermittent heavy I/O and idle I/O) with as small impact on performance
as possible.
medium_power mode allows the link to
transition between PARTIAL and fully-powered (that is "ACTIVE") states,
depending on the load. Note that it is not possible to transition a link
directly from PARTIAL to SLUMBER and back; in this case, either power
state cannot transition to the other without transitioning through the
ACTIVE state first.
max_performance
ALPM is disabled; the link does not enter any low-power state when there is no I/O on the disk.
To check whether your SATA host adapters actually support ALPM you can check if the file /sys/class/scsi_host/host*/link_power_management_policy
exists. To change the settings simply write the values described in
this section to these files or display the files to check for the
current setting.
Important — some settings disable hot plugging
Setting ALPM to min_power or medium_power will automatically disable the "Hot Plug" feature.
3.7. Relatime Drive Access Optimization
The POSIX standard requires that operating systems maintain file
system metadata that records when each file was last accessed. This
timestamp is called atime, and
maintaining it requires a constant series of write operations to
storage. These writes keep storage devices and their links busy and
powered up. Since few applications make use of the atime
data, this storage device activity wastes power. Significantly, the
write to storage would occur even if the file was not read from storage,
but from cache. For some time, the Linux kernel has supported a noatime option for mount and would not write atime
data to file systems mounted with this option. However, simply turning
off this feature is problematic because some applications rely on atime data and will fail if it is not available.
The kernel used in Red Hat Enterprise Linux 6 supports another alternative — relatime. Relatime maintains atime data, but not for each time that a file is accessed. With this option enabled, atime data is written to the disk only if the file has been modified since the atime data was last updated (mtime), or if the file was last accessed more than a certain length of time ago (by default, one day).
By default, all filesystems are now mounted with relatime enabled. To suppress this feature across an entire system, use the boot parameter default_relatime=0. If relatime
is enabled on a system by default, you can suppress it for any
particular file system by mounting that file system with the option norelatime. Finally, to vary the default length of time before which the system will update a file's atime data, use the relatime_interval= boot parameter, specifying the period in seconds. The default value is 86400.
3.8. Power Capping
Red Hat Enterprise Linux 6 supports the power capping features found in recent hardware, such as HP Dynamic Power Capping
(DPC), and Intel Node Manager (NM) technology. Power capping allows
administrators to limit the power consumed by servers, but it also
allows managers to plan data centers more efficiently, because the risk
of overloading existing power supplies is greatly diminished. Managers
can place more servers within the same physical footprint and have
confidence that if server power consumption is capped, the demand for
power during heavy load will not exceed the power available.
HP Dynamic Power Capping
Dynamic Power Capping is a feature available on select ProLiant and
BladeSystem servers that allows system administrators to cap the power
consumption of a server or a group of servers. The cap is a definitive
limit that the server will not exceed, regardless of its current
workload. The cap has no effect until the server reaches its power
consumption limit. At that point, a management processor adjusts CPU
P-states and clock throttling to limit the power consumed.
Dynamic Power Capping modifies CPU behavior independently of the operating system, however, HP's integrated Lights-Out 2
(iLO2) firmware allows operating systems access to the management
processor and therefore applications in user space can query the
management processor. The kernel used in Red Hat Enterprise Linux 6
includes a driver for HP iLO and iLO2 firmware, which allows programs to
query management processors at /dev/hpilo/dXccbN. The kernel also includes an extension of the hwmonsysfs interface to support power capping features, and a hwmon driver for ACPI 4.0 power meters that use the sysfs
interface. Together, these features allow the operating system and
user-space tools to read the value configured for the power cap,
together with the current power usage of the system.
Intel Node Manager imposes a power cap on systems, using processor
P-states and T-states to limit CPU performance and therefore power
consumption. By setting a power management policy, administrators can
configure systems to consume less power during times when system loads
are low, for example, at night or on weekends.
Intel Node Manager adjusts CPU performance using Operating System-directed configuration and Power Management (OSPM) through the standard Advanced Configuration and Power Interface.
When Intel Node Manager notifies the OSPM driver of changes to
T-states, the driver makes corresponding changes to processor P-states.
Similarly, when Intel Node Manager notifies the OSPM driver of changes
to P-states, the driver changes T-states accordingly. These changes
happen automatically and require no further input from the operating
system. Administrators configure and monitor Intel Node Manager with Intel Data Center Manager (DCM) software.
For further details of Intel Node Manager, refer to Node Manager — A Dynamic Approach To Managing Power In The Data Center, available from http://communities.intel.com/docs/DOC-4766
3.9. Enhanced Graphics Power Management
Red Hat Enterprise Linux 6 saves power on graphics and display devices
by eliminating several sources of unnecessary consumption.
LVDS reclocking
Low-voltage differential signaling (LVDS)
is an system for carrying electronic signals over copper wire. One
significant application of the system is to transmit pixel information
to liquid crystal display (LCD) screens in notebook computers. All displays have a refresh rate
— the rate at which they receive fresh data from a graphics controller
and redraw the image on the screen. Typically, the screen receives fresh
data sixty times per second (a frequency of 60 Hz). When a screen
and graphics controller are linked by LVDS, the LVDS system uses power
on every refresh cycle. When idle, the refresh rate of many LCD screens
can be dropped to 30 Hz without any noticeable effect (unlike cathode ray tube
(CRT) monitors, where a decrease in refresh rate produces a
characteristic flicker). The driver for Intel graphics adapters built
into the kernel used in Red Hat Enterprise Linux 6 performs this downclocking automatically, and saves around 0.5 W when the screen is idle.
Enabling memory self-refresh
Synchronous dynamic random access memory
(SDRAM) — as used for video memory in graphics adapters — is recharged
thousands of times per second so that individual memory cells retain the
data that is stored in them. Apart from its main function of managing
data as it flows in and out of memory, the memory controller is normally
responsible for initiating these refresh cycles. However, SDRAM also
has a low-power self-refresh mode. In this
mode, the memory uses an internal timer to generate its own refresh
cycles, which allows the system to shut down the memory controller
without endangering data currently held in memory. The kernel used in
Red Hat Enterprise Linux 6 can trigger memory self-refresh in Intel
graphics adapters when they are idle, which saves around 0.8 W.
GPU clock reduction
Typical graphical processing units (GPUs) contain internal clocks
that govern various parts of their internal circuitry. The kernel used
in Red Hat Enterprise Linux 6 can reduce the frequency of some of the
internal clocks in Intel and ATI GPUs. Reducing the number of cycles
that GPU components perform in a given time saves the power that they
would have consumed in the cycles that they did not have to perform. The
kernel automatically reduces the speed of these clocks when the GPU is
idle, and increases it when GPU activity increases. Reducing GPU clock
cycles can save up to 5 W.
GPU powerdown
The Intel and ATI graphics drivers in Red Hat Enterprise Linux 6 can
detect when no monitor is attached to an adapter and therefore shut down
the GPU completely. This feature is especially significant for servers
which do not have monitors attached to them regularly.
3.10. RFKill
Many computer systems contain radio transmitters, including Wi-Fi,
Bluetooth, and 3G devices. These devices consume power, which is wasted
when the device is not in use.
RFKill is a subsystem in the Linux kernel
that provides an interface through which radio transmitters in a
computer system can be queried, activated, and deactivated. When
transmitters are deactivated, they can be placed in a state where
software can reactive them (a soft block) or where software cannot reactive them (a hard block).
The RFKill core provides the application programming interface (API)
for the subsystem. Kernel drivers that have been designed to support
RFkill use this API to register with the kernel, and include methods for
enabling and disabling the device. Additionally, the RFKill core
provides notifications that user applications can interpret and ways for
user applications to query transmitter states.
The RFKill interface is located at /dev/rfkill,
which contains the current state of all radio transmitters on the
system. Each device has its current RFKill state registered in sysfs. Additionally, RFKill issues uevents for each change of state in an RFKill-enabled device.
Rfkill is a
command-line tool with which you can query and change RFKill-enabled
devices on the system. To obtain the tool, install the rfkill package.
Use the command rfkill list to obtain a list of devices, each of which has an index number associated with it, starting at 0. You can use this index number to tell rfkill to block or unblock a device, for example:
rfkill block 0
blocks the first RFKill-enabled device on the system.
You can also use rfkill to block certain categories of devices, or all RFKill-enabled devices. For example:
rfkill block wifi
blocks all Wi-Fi devices on the system. To block all RFKill-enabled devices, run:
rfkill block all
To unblock devices, run rfkill unblock instead of rfkill block. To obtain a full list of device categories that rfkill can block, run rfkill help
3.11. Optimizations in User Space
Reducing the amount of work performed by system hardware is
fundamental to saving power. Therefore, although the changes described
in Chapter 3, Core Infrastructure and Mechanics
permit the system to operate in various states of reduced power
consumption, applications in user space that request unnecessary work
from system hardware prevent the hardware from entering those states.
During the development of Red Hat Enterprise Linux 6, audits were
undertaken in the following areas to reduce unnecessary demands on
hardware:
Reduced wakeups
Red Hat Enterprise Linux 6 uses a tickless kernel (refer to Section 3.4, “Tickless Kernel”), which allows the CPUs to remain in deeper idle states longer. However, the timer tick
is not the only source of excessive CPU wakeups, and function calls
from applications can also prevent the CPU from entering or remaining in
idle states. Unnecessary function calls were reduced in over 50
applications.
Reduced storage and network IO
Input or output (IO) to storage devices and network interfaces forces
devices to consume power. In storage and network devices that feature
reduced power states when idle (for example, ALPM or ASPM), this traffic
can prevent the device from entering or remaining in an idle state, and
can prevent hard drives from spinning down when not in use. Excessive
and unnecessary demands on storage have been minimized in several
applications. In particular, those demands that prevented hard drives
from spinning down.
Initscript audit
Services that start automatically whether required or not have great
potential to waste system resources. Services instead should default to
"off" or "on demand" wherever possible. For example, the BlueZ
service that enables Bluetooth support previously ran automatically
when the system started, whether Bluetooth hardware was present or not.
The BlueZ initscript now checks that Bluetooth hardware is present on the system before starting the service.
This chapter describes two types of use case to illustrate the
analysis and configuration methods described elsewhere in this guide.
The first example considers typical servers and the second is a typical
laptop.
4.1. Example — Server
A typical standard server nowadays comes with basically all of the
necessary hardware features supported in Red Hat Enterprise Linux 6. The
first thing to take into consideration is the kinds of workloads for
which the server will mainly be used. Based on this information you can
decide which components can be optimized for power savings.
Regardless of the type of server, graphics performance is generally
not required. Therefore, GPU power savings can be left turned on.
Webserver
A webserver needs network and disk I/O. Depending on the external
connection speed 100 Mbit/s might be enough. If the machine serves
mostly static pages, CPU performance might not be very important.
Power-management choices might therefore include:
no disk or network plugins for tuned.
ALPM turned on.
ondemand governor turned on.
network card limited to 100 Mbit/s.
Compute server
A compute server mainly needs CPU. Power management choices might include:
depending on the jobs and where data storage happens, disk or network plugins for tuned; or for batch-mode systems, fully active tuned.
depending on utilization, perhaps the performance governor.
Mailserver
A mailserver needs mostly disk I/O and CPU. Power management choices might include:
ondemand governor turned on, because the last few percent of CPU performance are not important.
no disk or network plugins for tuned.
network speed should not be limited, because mail is often internal
and can therefore benefit from a 1 Gbit/s or 10 Gbit/s link.
Fileserver
Fileserver requirements are similar to those of a mailserver, but
depending on the protocol used, might require more CPU performance.
Typically, Samba-based servers require more CPU than NFS, and NFS
typically requires more than iSCSI. Even so, you should be able to use
the ondemand governor.
Directory server
A directory server typically has lower requirements for disk I/O,
especially if equipped with enough RAM. Network latency is important
although network I/O less so. You might consider latency network tuning
with a lower link speed, but you should test this carefully for your
particular network.
4.2. Example — Laptop
One other very common place where power management and savings can
really make a difference are laptops. As laptops by design normally
already use drastically less energy than workstations or servers the
potential for absolute savings are less than for other machines. When in
battery mode, though, any saving can help to get a few more minutes of
battery life out of a laptop. Although this section focuses on laptops
in battery mode, but you certainly can still use some or all of those
tunings while running on AC power as well.
Savings for single components usually make a bigger relative
difference on laptops than they do on workstations. For example, a
1 Gbit/s network interface running at 100 Mbits/s saves around
3–4 watts. For a typical server with a total power consumption of
around 400 watts, this saving is approximately 1 %. On a
laptop with a total power consumption of around 40 watts, the power
saving on just this one component amounts to 10 % of the total.
Specific power-saving optimizations on a typical laptop include:
Configure the system BIOS to disable all hardware that you do not
use. For example, parallel or serial ports, card readers, webcams, WiFi,
and Bluetooth just to name a few possible candidates.
Dim the display in darker environments where you do not need full illumination to read the screen comfortably. Use System+Preferences → Power Management on the GNOME desktop, Kickoff Application Launcher+Computer+System Settings+Advanced → Power Management on the KDE desktop; or gnome-power-manager or xbacklight at the command line; or the function keys on your laptop.
Use the laptop-battery-powersave profile of tuned-adm
to enable a whole set of power-saving mechanisms. Note that performance
and latency for the hard drive and network interface are impacted.
Additionally (or alternatively) you can perform many small adjustments to various system settings:
use the ondemand governor (enabled by default in Red Hat Enterprise Linux 6)
enable laptop mode (part of the laptop-battery-powersave profile):
echo 5 > /proc/sys/vm/laptop_mode
increase flush time to disk (part of the laptop-battery-powersave profile):
mount filesystem using relatime (default in Red Hat Enterprise Linux 6):
mount -o remount,relatime mountpoint
activate best power saving mode for hard drives (part of the laptop-battery-powersave profile):
hdparm -B 1 -S 200 /dev/sd*
disable CD-ROM polling (part of the laptop-battery-powersave profile):
hal-disable-polling --device /dev/scd*
reduce screen brightness to 50 or less, for example:
xbacklight -set 50
activate DPMS for screen idle:
xset +dpms; xset dpms 0 0 300
reduce Wi-Fi power levels (part of the laptop-battery-powersave profile):
for i in /sys/bus/pci/devices/*/power_level ; do echo 5 > $i ; done
deactivate Wi-Fi:
echo 1 > /sys/bus/pci/devices/*/rf_kill
limit wired network to 100 Mbit/s (part of the laptop-battery-powersave profile):
ethtool -s eth0 advertise 0x0F
Tips for Developers
Every good programming textbook covers problems with memory allocation
and the performance of specific functions. As you develop your
software, be aware of issues that might increase power consumption on
the systems on which the software runs. Although these considerations do
not affect every line of code, you can optimize your code in areas
which are frequent bottlenecks for performance.
Some techniques that are often problematic include:
using threads.
unnecessary CPU wake-ups and not using wake-ups efficiently. If you
must wake up, do everything at once (race to idle) and as quickly as
possible.
using [f]sync() unnecessarily.
unnecessary active polling or using short, regular timeouts. (React to events instead).
not using wake-ups efficiently.
inefficient disk access. Use large buffers to avoid frequent disk access. Write one large block at a time.
inefficient use of timers. Group timers across applications (or even across systems) if possible.
excessive I/O, power consumption, or memory usage (including memory leaks)
performing unnecessary computation.
The following sections examine some of these areas in greater detail.
A.1. Using Threads
It is widely believed that using threads makes applications perform better and faster, but this is not true in every case.
Python
Python uses the Global Lock Interpreter[1], so threading is profitable only for larger I/O operations. Unladen-swallow[2] is a faster implementation of Python with which you might be able to optimize your code.
Perl
Perl threads were originally created for applications running on
systems without forking (such as systems with 32-bit Windows operating
systems). In Perl threads, the data is copied for every single thread
(Copy On Write). Data is not shared by default, because users should be
able to define the level of data sharing. For data sharing the threads::shared
module has to be included. However, data is not only then copied (Copy
On Write), but the module also creates tied variables for the data,
which takes even more time and is even slower. [3]
C
C threads share the same memory, each thread has its own stack, and
the kernel does not have to create new file descriptors and allocate new
memory space. C can really use the support of more CPUs for more
threads. Therefore, to maximize the performance of your threads, use a
low-level language like C or C++. If you use a scripting language,
consider writing a C binding. Use profilers to identify poorly
performing parts of your code. [4]
A.2. Wake-ups
Many applications scan configuration files for changes. In many
cases, the scan is performed at a fixed interval, for example, every
minute. This can be a problem, because it forces a disk to wake up from
spindowns. The best solution is to find a good interval, a good checking
mechanism, or to check for changes with inotify and react to events. Inotify can check variety of changes on a file or a directory.
For example:
int fd;
fd = inotify_init();
int wd;
/* checking modification of a file - writing into */
wd = inotify_add_watch(fd, "./myConfig", IN_MODIFY);
if (wd < 0) {
inotify_cant_be_used();
switching_back_to_previous_checking();
}
...
fd_set rdfs;
struct timeval tv;
int retval;
FD_ZERO(&rdfs);
FD_SET(0, &rdfs);
tv.tv_sec = 5;
value = select(1, &rdfs, NULL, NULL, &tv);
if (value == -1)
perror(select);
else {
do_some_stuff();
}
...
The advantage of this approach is the variety of checks that you can perform.
The main limitation is that only a limited number of watches are available on a system. The number can be obtained from /proc/sys/fs/inotify/max_user_watches and although it can be changed, this is not recommended. Furthermore, in case inotify fails, the code has to fall back to a different check method, which usually means many occurrences of #if #define in the source code.
For more information on inotify, refer to the inotify man page.
A.3. Fsync
Fsync is known as an I/O expensive operation, but this is is not completely true. For example, refer to Theodore Ts'o's article Don't fear the fsync![5] and the accompanying discussion.
Firefox used to call the sqlite library each time the user clicked on a link to go to a new page. Sqlite called fsync
and because of the file system settings (mainly ext3 with data-ordered
mode), there was a long latency when nothing happened. This could take a
long time (up to 30 seconds) if another process was copying a large
file at the same time.
However, in other cases, where fsync
wasn't used at all, problems emerged with the switch to the ext4 file
system. Ext3 was set to data-ordered mode, which flushed memory every
few seconds and saved it to a disk. But with ext4 and laptop_mode, the
interval between saves was longer and data might get lost when the
system was unexpectedly switched off. Now ext4 is patched, but we must
still consider the design of our applications carefully, and use fsync as appropriate.
The following simple example of reading and writing into a
configuration file shows how a backup of a file can be made or how data
can be lost:
/* open and read configuration file e.g. ~/.kde/myconfig */
fd = open("./kde/myconfig", O_WRONLY|O_TRUNC|O_CREAT);
read(myconfig);
...
write(fd, bufferOfNewData, sizeof(bufferOfNewData));
close(fd);
